(702) 870 - 0006
24/7 Emergency Service

What Is Trenchless Pipelining?

A low cost alternative to fixing broken pipes

Posted 14:26 June 29, 2021
Last Updated 08:03 August 09, 2021

All Articles

A cured-in-place pipe (CIPP) is one of many trenchless repair methods used to repair and restore existing pipelines. CIPP is a pipe inside a pipe. It is seamless and without joints. A wide range of pipe diameters can be rehabilitated. CIPP can repair pipelines with diameters as small as 4 inches and as large as 100 inches or more. Common applications are for sewer, water, gas, and chemical pipelines.

How CIPP Works

Very little digging is required with CIPP repair. After the point of repair is identified, an entry and exit point are excavated. The damaged pipe is cleared of any blockages. Hydro Jetting may be used to help clear blockages.

A resin-saturated tube that is made of polyester, fiberglass, or another similar material is pulled through the damaged pipe. Inside the liner is a balloon that is inflated with either air or water. The tube is held in place with the balloon and allowed to cure. Curing can be accelerated with heat, steam, hot water, or ultra violet light.

After the tube has fully cured the balloon is deflated and removed. The new pipe is inspected with a CCTV video feed. After a successful inspection the new pipe is ready to use. Due to the lower excavation requirements of trenchless pipe lining, it is often less expensive and less disruptive than traditional, "dig up and replace" pipeline repair methods.


Eric Wood invented cured-in-place pipe technology in London, England in 1971. His name for the technology was insitu form. The name is Latin and means form in place. Wood applied for a US patent in 1975 and it was granted in 1977. Insituform Technologies (from Wood's original name) was created. They held the patent and were the only company allowed to utilize trenchless pipelining repair technology.

In the late 1970's Insituform Technologies began commercial and residential applications in Japan and Europe. In the early 1980's the process started being used in residential applications in the United States. In 1994 the patent expired and CIPP technology has been in the public domain ever since. Numerous companies immediately emerged and started using CIPP repair.


If a pipeline is leaking, broken, or structurally unsound, CIPP offers an attractive alternative to traditional "dig up and replace" pipeline repair methods. Sometimes existing access points are enough to undertake a repair. In this case no excavation is required at all. If excavation is required it is usually minimal and does not require extensive disruption to the premises.

CIPP has a smooth interior. There are no joints. As a result, CIPP can repair pipes with bends. Special design considerations must be made when repairing bends, in order to prevent stretching and wrinkling.

Modern CCTV video technology is readily available. It is easy to inspect new pipelines.

The overall cost of CIPP is oftentimes far less than that of traditional pipeline repair.

72 inch pipeline repair project by Insituform Technologies for the City of Tampa


Any blockages that exist in the broken pipeline must be cleared before CIPP repair can be done.

The time for CIPP to cure varies depending on the size of the project. Cure time ranges from a few hours to 30 hours or more. During this time period the flow to the existing pipeline must be totally bypassed or shut off. The curing process must be carefully monitored. After curing, the new pipeline must be thoroughly inspected and tested.

Repairing bends must be undertaken carefully. Special liners must be used that resist wrinkling. The larger the diameter of pipe, the more likely it is that a bend can be repaired. The liner material used in common sizes is oftentimes made of a felted fabric (non-woven) that does not go around bends well and liner wrinkling may result. When repairing bends, a liner made of a woven fabric is required.

After a pipeline has been repaired with CIPP, the pipeline can no longer be snaked with a machine. The pipeline must be cleaned via Hydro Jetting.

All Trades

We are experts in CIPP and trenchless pipe lining. We have the equipment and experience that you need. Let us evaluate your situation and determine if trenchless pipe lining is a viable solution for you. If it is, you may be able to get that broken pipe repaired at lower cost and with minimal site disruption.

All Trades services Las Vegas, Henderson, and Boulder City, Nevada. We offer fast professional service at reasonable rates.

All Articles
Contact Information
All Trades Las Vegas
4001 S Decatur Blvd STE 37-251
Las Vegas, NV 89103

(702) 870 - 0006
We Accept
visa mastercard discover american express cash

Work For Us
Apply Online
Nevada State Contractor Board License Numbers:
License #0083055 (Plumbing)
License #0083054 (Air Conditioning)
License #0085369 (Electrical)
Bid Limit $950,000


Terms of Service, Privacy Policy, & Cookie Statement

© 2013 - 2024 All Trades Las Vegas.
All rights reserved.